These instructions apply to the Skoda Kamiq Mk1 (NW4) 2019-Present.
For other models, please choose your vehicle here.
Changing the blades or freeing them from ice on a Skoda Kamiq (NW4, 2019–present) means first lifting the wiper arms into their service position. Park them normally and they sit under the bonnet lip out of reach — here’s the proper way up. The service position (some owners call it the winter or maintenance position) swings both front arms up to vertical and holds them there, clear of the glass and the scuttle trim, so you can unclip a worn blade or stand the arms up before a hard frost so they don’t freeze flat to the screen. It’s a normal built-in feature, not a fault, and on the Kamiq it’s triggered from the wiper stalk rather than from anything under the bonnet.
Why the Service Position Exists
The Kamiq parks its wiper arms low, tucked below the rear edge of the bonnet trim so they sit out of the airflow and out of sight. It looks neat, but it puts the pivot end of each arm behind the plastic scuttle panel. Grab a parked arm and haul it upright and it fouls the bonnet lip on the way up: you risk bending the arm, popping the blade clip off, or chipping the paint along the bonnet edge. Lifting the arms into their proper service position first clears them of that trim, giving you full travel and a clean, square angle to work at, and it moves the arms through the linkage the way the motor intends rather than putting a sideways strain on a cold mechanism.
Before You Start
- Close the bonnet. On the Kamiq the mode won’t arm with the bonnet up, and a raised arm can clash with an open bonnet anyway.
- Get the ignition state right. The method below needs the ignition switched on and then off — read it through once before you touch the stalk.
- Free any frozen blades first. If the rubber is iced to the screen, ease it loose by hand or with de-icer; driving a stuck blade can strain the linkage or blow a fuse.
- Have the new blades to hand. Once the arms are up, swap quickly and lower them again rather than leaving them standing.
- Work one arm at a time. Lift, change or clear one side, lay it back down, then do the other so both arms stay supported.
Raising the Wipers
- Check the bonnet is shut — the mode won’t arm otherwise.
- Switch the ignition on, then off.
- Within a few seconds, flick the wiper stalk down (single-wipe) briefly.
- The arms sweep up and hold vertical.
- Pull them off the glass to change blades or clear snow.
Some Kamiqs also list a wiper service position in the infotainment menu; if yours offers it there, it does exactly the same job as the stalk method above.
Putting Them Back
Lay the arms back down flat against the glass first — never let them snap back on their own, as an unsupported arm can crack the screen. Then switch the ignition on and run the wipers once to return them to their normal parked spot under the bonnet lip. Give the screen a quick spray and a wipe afterwards to confirm both arms sit level and sweep cleanly.
Won’t Lift?
- Too slow — the stalk only works for a few seconds after ignition-off; start again and flick it promptly.
- Wrong ignition state — you need the on-then-off sequence, not the engine running or the car fully asleep.
- Bonnet ajar — latch it fully; a bonnet only on its first catch can block the mode.
- Blades frozen down — free them by hand first so the motor isn’t fighting the ice.
- Arms not parked — make sure the wipers are in their normal rest spot before you try, then retry the sequence.
- Try the menu — if your car lists the service position in the infotainment screen, use that instead.
Changing the Blades
With an arm standing vertical, support it with one hand so it can’t drop while you work. Most Kamiq blades use a common clip or hook fitting that releases with a small tab — press or pinch it, slide the old blade off the arm, and click the new one home until you feel it seat. Check it’s locked before you let go, then lower the arm gently back to the glass rather than releasing it from height, so the sprung arm never taps the screen.
Frequently Asked Questions
How do I set the Skoda Kamiq wipers to service position?
Switch the ignition on and then off, and within a few seconds flick the wiper stalk down for a single wipe. The arms sweep up and hold vertical. A menu option exists on some cars via the infotainment screen.
Do I need any tools?
No. The whole thing is done from the wiper stalk (or the infotainment menu if your car has it). You only need the new blades themselves if you’re renewing them — nothing to raise or lower the arms.
How do I get the wipers back down again?
Fold the arms flat onto the glass by hand, switch the ignition on, and run the wipers once. They return to their normal parked position under the bonnet lip. Don’t let the arms spring back on their own.
Can I just lift the wipers at their parked position?
It’s best not to. Parked, the arms sit under the bonnet trim, so forcing them up from there risks bending an arm or chipping paint. The service position lifts them clear first, which is why it exists.
Why won’t my Kamiq enter the service position?
Usually the timing: the stalk only responds for a few seconds after you switch the ignition off. Also check the bonnet is fully latched and the blades aren’t frozen down, then try the sequence again promptly.
Does the service position reset anything on the car?
No. It only moves the wiper arms — it doesn’t clear service reminders, faults or settings. It’s purely a mechanical convenience for changing blades or standing the arms up in frost.
Doing more after a battery change? See our Kamiq window re-initialise guide. For warning lights, look up the code on autodtcs.com.
Independent guide — not affiliated with Skoda. Always follow your official service manual and safety precautions. Read our full disclaimer.