These instructions apply to the Land Rover Discovery Mk5 (L462) 2017-Present.
For other models, please choose your vehicle here.
When the oil-service reminder appears on your Land Rover Discovery (2017–present), you can reset the service counter yourself with a pedal sequence — no dealer for the routine oil reset. Here’s the owner method for the L462 Discovery.
The service message on the fifth-generation Discovery (L462) is a scheduled-maintenance reminder, not a fault. The instrument cluster keeps track of how far the car has travelled and how long it has been since the last service, and when that counter runs down it shows a spanner symbol or a ‘service required’ message. It doesn’t signal an engine problem — it simply means the oil and the routine checks are due. Once the work is finished, the counter needs resetting so the Discovery begins a fresh interval and the reminder stops appearing at every start-up.
The reset is a straightforward pedal sequence you can perform from the driver’s seat in about a minute. It clears the oil-service counter and switches off the reminder. No tools, no code and no garage visit are needed for this step — just the car, the key and a couple of minutes.
What the Service Light Means
The Discovery uses an interval-based service reminder. The cluster counts down the distance and elapsed time remaining until the next scheduled service and warns you as that point approaches. A spanner symbol, or a message such as ‘service required’, tells you the interval has been reached. Because it is a reminder rather than a fault warning, it keeps appearing at start-up until the counter is reset — even after the oil has been changed. Resetting is what tells the car the service has been done.
Keep it separate from red or amber warning lights that report a genuine fault (oil pressure, engine, brakes and so on). Those store a diagnostic code and won’t clear with a service reset. If one of those is showing alongside the spanner, address the fault first.
Before You Begin
Only reset the reminder after the oil change and any due maintenance are genuinely complete — resetting the counter on a car that still needs the work just hides the reminder. Park on level ground with the transmission in Park and the electronic parking brake applied. Switch the ignition on but leave the engine off for the whole sequence. No tools are required. Make sure you can see the instrument cluster clearly so you can watch the service display change.
Resetting the Service Indicator
- Switch the ignition on (don’t start the engine).
- Open the bonnet and open the driver’s door.
- Fully depress both the accelerator and brake pedals together and hold for about 10 seconds.
- The service reset display appears — release the pedals.
- Switch the ignition off, then on, and check the service indicator has gone out. Repeat if needed.
When a Dealer Tool Is Needed
The pedal method clears the oil counter. On some cars the full service-interval display won’t accept a reset this way — then the complete reset needs Land Rover diagnostic equipment. For a routine oil change, the pedal reset is usually all you need.
If the Reset Doesn’t Work
If the reminder is still showing after your first attempt, run through these before assuming anything is wrong:
- Check the ignition position. The ignition must be on (dash lit) but the engine off. If the engine started, switch fully off and begin again.
- Hold both pedals fully for the full 10 seconds with the bonnet and driver’s door open — a half-press or an early release cancels the sequence.
- Wait for the display to change before you lift off. Release the pedals only once the service reset display has appeared.
- Cycle the ignition off and on to confirm the indicator has cleared, then repeat the whole sequence if it hasn’t.
- A separate warning light? A fault stores a code — look it up on autodtcs.com.
After the Reset
When the reset takes, the spanner symbol or service message disappears and does not return at the next start-up. The cluster starts a new service interval, counting down again from full. If the message is still there the following time you start the car, the reset didn’t register — run the sequence again, holding the pedals for the full ten seconds.
How Often You’ll Need This
Reset the service indicator every time the scheduled oil service is carried out — once per service, right after the work. The Discovery’s service intervals are distance- and time-based, so the exact mileage or months between services depends on the engine and how the car is driven. Follow the interval printed in your vehicle handbook rather than a fixed figure, and reset only when that service is genuinely done.
Frequently Asked Questions
How do I reset the service light on a Land Rover Discovery?
Ignition on, bonnet and driver’s door open, press the accelerator and brake together for 10 seconds, then cycle the ignition.
Do I need a diagnostic tool?
Not for the oil-counter reset — that’s the pedal method. A full service-display reset can need a dealer tool on some cars.
Why must the bonnet and door be open?
The car only accepts the reset with the bonnet and driver’s door open and the ignition on.
Is the spanner light a fault or engine problem?
Neither — it’s a scheduled-maintenance reminder telling you a service is due. It doesn’t indicate a mechanical fault, and it clears once the counter is reset.
How often should I reset it?
After every scheduled oil service. The interval is distance- and time-based, so follow the figure in your handbook for your engine.
The light came back — why?
The reset probably didn’t register; repeat it, holding both pedals fully for the 10 seconds.
If another warning light appeared with the service message, our sister site autodtcs.com can help you decode it.
Independent guide — not affiliated with Land Rover. Always follow your official service manual and safety precautions. Read our full disclaimer.